12V 24V Automotive Probe Circuit Tester Power Electrical System Diagnostic Tool

Description: 12V 24V Automotive Probe Circuit Tester Power Electrical System Diagnostic Tool Ancel PB500-12V 24V Circuit Tester With the PB500 probe tester, you can check voltage and ground signals in a typical DC circuit. However, the kicker is that you can also use it to send voltage and ground signals. It works like a test light that can power circuits or provide a good known ground. This way, you can effectively test components and circuits without having to break out the old alligator clips and jumper wires. You can power or ground a circuit directly through the top of the device. Product Features:✔️DC voltage range: 0-65V; Resistance range: 0-100 kΩ; Rated current: 1-10 amps; Frequency response of sound passage: 0Hz to 10Khz. ✔️Perform current injection, measurement, ground test, polarity test, continuity test and component activation. ✔️Ergonomic housing design with waterproof, rugged, blow-molded housing, easy to handle and store. ✔️There are 4 modes to diagnose the electrical systems.(DC voltage, AC voltage, Resistance, Diode) ✔️AC- RMS, AC peak to peak, frequency and pulse width for signal testing. ✔️High voltage capability: displays up to 60 volts, 0.1 volt resolution. ✔️8-amp circuit breaker, automatic reset, no button to press. ✔️Three additional modes: MIN / MAX / audible monitoring. ✔️Automatically detects positive, negative and open circuit. ✔️Large color screen LCD with easy to navigate user menu. ✔️Comes with an additional 20ft extension cable. ✔️Find shorts to ground and to voltage. Circuit Protection The PB500 has a built-in 8-amp circuit breaker to prevent circuit overload and overheating. Unlike a normal test lamp, this device can conduct direct battery current into the circuit you touch with it. Any time you backfeed a circuit, you need to know what you are doing. The breaker will protect the circuit, but 8 amps is still enough to do a lot of damage with the wrong wire. Voltage Indicator The LED indicator on the front of the unit will show you the battery voltage when it is connected. You can use it to determine a whole range of things. You can even do a quick check of the alternator by plugging it in and starting the car. The voltage should go from about 12.6 volts to 14.0 volts. This is also useful if you have a situation where a power supply has a large voltage drop, if you notice low voltage on certain branches when checking fuses, etc. More uses are worth your expectation！ ➤ Find The Short Circuits: In most cases, a short circuit will appear as a blown fuse or a tripping of an electrical protection device.Use the probe tip to activate and energize each of the fuse contacts..The contact which trips the circuit breaker is the shorted circuit. ➤ Find The Bad Ground: Probe the suspected ground wire or contact with the probe tip. If the circuit breaker tripped, this circuit is more than likely a good ground. ➤ Testing Trailer Lights: While the tool in DC Voltage mode, clip the auxiliary ground lead to the trailer ground , probe the contacts at the jack and then apply voltage to the probe tip. This lets you check the function and orientation of the connector and trailer lights. ➤ Continuity Testing While the tool is in Resistance mode, using the probe tip with chassis is ground or the auxiliary ground lead, continuity can be tested on wires and components attached or disconnected from the vehicle’s electrical system. When the probe tip is contacting a good ground, the LCD will indicate “0.0Ω” and green LED will be on. A beep tone will sound. ➤ Activating Component: The component activation function is designed to generate activation signals to the tested components, such as activating lights, motors and other on-board electric equipments. ➤ Signal Circuit Testing: Once you extract a DTC from the vehicle and realize that troubleshooting begins with some kind of sensor circuit, there is a quick test you can perform to verify the code. Testing your sensor is easy while using the tool. ➤ Voltage & Polarity Testing: While the tool is in DC Voltage mode, contact the probe tip to a POSITIVE circuit. The red LED will light and the LCD displays the voltage with a resolution of 0.1V. A beep tone will sound. If contact the probe tip to a NEGATIVE circuit, the green LED will light and the LCD displays the voltage with a resolution of 0.1V. A beep tone will sound. If contact the probe tip to an OPEN circuit, neither of the LED will light. ANCEL PB500 Product Function:There are four modes to diagnose the electrical systems, which can be accessed by depressing the Mode Button and cycling through each one.✔️DC voltage: While the tool in this mode, contact the probe tip to a circuit, then the LCD display will read the DC voltage with a resolution of 0.1 volt.✔️AC voltage: While the tool in this mode, contact the probe tip to a circuit, then the LCD display will read the Max. voltage, the Min. Voltage and frequency.✔️Resistance: While the tool in this mode, contact the probe tip to a circuit, then the LCD display will read the resistance between the tip and auxiliary ground lead.✔️Diode: In this mode, the probe tip contact the positive terminal of the diode, connect the auxiliary ground lead to the negative terminal of the diode, the screen will display the forward voltage drop, indicates the forward bias. If exchange the probe tip and auxiliary ground lead, the screen will not display the voltage, indicates the reversebias. Trailer WiringThe PB500 Circuit Tester features a long 20-foot cable that allows you to make the initial connection directly to the vehicle's battery, while providing easy access to connect the trailer harness at the rear of the vehicle. Specifications:◆ Display: TFT color display (160 x 128 dpi) ◆ Operating Temperature: 0 to 60C (32 to 140F) ◆ External Power: 12.0 or 24.0 V power provided via vehicle battery ◆ DC voltage range: 0-65V +1digit ◆ Resistance range: 0-100 kΩ ◆ Frequency response of tone pass through 0Hz to 10Khz. ◆ Circuit Breaker ◆ Rating current: 1-10 Amp ◆ Testing Standard: 100% current: Hold > 1 hour 150% current: trip in one hour 200% current: trip in 3-30 seconds. 300% current: trip in 0.5-4.0 seconds. What Do You Get? 1 x PB500 Circuit Probe 1 x Extension Cable (20ft) 1 x Battery Hookup Clips 1 x Cigarette Lighter Adapter 1 x Protective Case 1 x Probe tip 1 x User's Manual PAYMENTDELIVERY DETAILSTERMS OF SALESABOUT USCONTACT USPAYMENTWe accept Credit cards、Debit card、Apple Pay、Google Pay etc.payment.Please contact us if you need to use another method to pay.Payment should be made within 4 days after bidding ends.Otherwise an Unpaid Item case will be opened to you.We are not responsible for buyers’ local taxes.Please include your special requests in eBay note if there is any. We reserve the final right of sellingDELIVERY DETAILSOrder will be shipped within 1 business day after payment confirmed.We have warehouse in USA，UK，HongKong，Australia，Russian，Germany and China warehouse.From our US/UK/RU/DE/AU warehouse via USPS or UPS eCommerce shipping,Delivery time varies from 2 to 6 business days.From our China warehouse via DHL or Fedex,Delivery time varies from 5-12 business days.We will ship according to your payment address,Please make sure it is correct and include phone number for delivery.If you do not receive your order in the estimated time, please contact us, we would do our best to serve you solve the problem.Please include your special requests in eBay note if there is any.TERMS OF SALESWe can not guarantee that you will be able to access every module or use every piece of cd/dvd software. Compatibility varies due to variations in the cars modlue or availabilty of year it released from original factory.We don't take charge to complete clearance when parcel arrived at your Customs(Because we sold at a low price,good quality,limited profit only),but we will do all what we can to help you get your package.Please do not hesitate to leave us your positive feedback if you are happy with your shopping. if you are just a little satisfied with your purchase, please do not leave us negative or neutral feedback before contacting us.We are not responsible for Buyer's Local TaxsABOUT US1.ANCEL specializes in automotive intelligent diagnostics, detection and analysis systems, and automotive-related products for mechanics, repair shops, and DIYers.2.Our independent brand is ANCEL (welcome to visit the official website to view）At the same time, we also represent other brands such asFOXWELL, LAUNCH, AUTOPHIX,OBDPROG ectAll products are 100% genuine, and we provide free return/exchange/refund services as well as technical support. If there are any after-sales or pre-sales messages that can be sent to us, we will promptly handle them and provide satisfactory solutions CONTACT USIf you are satisfied with our product or our service, please leave Positive Feedback 5-Stars ★★★★★If you have any question,please feel free to contact us first before you leave feedback , we will try our best to solve the problemBusiness time: GMT8( 9:00 am-6:30 pm) monday to saturdayBrandANCELManufacturer Part NumberANCEL PB500 Power Scan Circuit TesterVolt24 voltAccessoriesCarrying Case, Clamps, Probes, User GuideFeaturesAnalog Display, Continuity Testing, Digital Display, Relay & Component Testing, VoltmeterVehicle TypeHeavy Duty/Commercial, Passenger VehicleWarranty5 YearRating Current1-10 AmpDisplayTFT Color Display (160 x 128 DPI)DC Voltage Range0-65V +1digitOperating Temperature0 to 60C (32 to 140F)Resistance Range0-100 kΩExternal Power12.0 or 24.0 VOn Sep 10, 2024 at 14:13:59 PDT, seller added the following information:

Price: 111.99 USD

Location: Los Angeles, California

End Time: 2024-10-10T03:20:28.000Z

Shipping Cost: 0 USD