GrimmSpeed Cold Air Intake Black For Subaru 02-07 WRX/STI 04-08 FXT

Description: Manufacturer: GrimmSpeed Part Number: 060074 Condition: New Product Description: Finally a GD intake with the looks to match its performance. It's no secret that GrimmSpeed intakes feature performance and aesthetics that lead the pack. With years of Design theories and knowledge gained from our successful intake program, we have developed solutions that increase power and are very easy to Install and tune. The only thing we were missing was an intake system for early models, and after nearly two years of development and testing we are extremely proud to offer what we feel is the Best intake for your 2002-2007 Subaru WRX and STI, and 2004-2008 Subaru Forester XT. Quick Specs: Hybrid Cold Air/Short Ram Design - Combining the advantages and eliminating the negatives of both traditional intake Designs Air straightener A key component for accurate and consistent MAF sensor readings. Custom reusable high flow air filter - Integrated velocity stack entrance smooths incoming air StealthBox Heatshield - Our signature heatshield Design which provides cool air while hiding ugly components Made in the USA - Right here in Minnesota, in fact 40 min Installation - Extremely simple with our written and video guides Design Our Design requirements for this intake are similar to our others: the intake should Reduce as much restriction as possible, it should be easy to tune and accurately measure incoming airflow, it should properly filter out potentially harmful particles, and it should look like something you're proud to have in your engine bay. We Designed this intake to meet these goals by using only minimal bend angle and pipe length which helps to decrease restriction. Additionally, our low restriction washable air filter helps here too, while still filtering particles down to 5 microns. We have also incorporated an air straightener into our Design, an invaluable feature that was Not utilized on the OEM airbox until later models. Finally, we have continued our StealthBox heatshield Design, utilizing it to Not only keep hot air away from the air filter, but to cover up unsightly components such as the ABS pump. Less obvious features of this intake include the location of the air filter. Specifically that we made sure that the filter is Not close enough to the ground such that water/hydrolocking is a concern. The heatshield also contains provisions to mount the factory clips that hold the two coolant hoses that would traditionally mount to the OEM airbox. This keeps them out of the way and maintains a clean aesthetic. The Design of the heatshield also acts to hide the power steering pump reservoir, but does Not hinder inspection or filling. Overall what is accomplished is a true hybrid of traditional Cold Air Intakes and Short Ram Intakes, with all the advantages and none of the compromises. This engineering study from our 08-14 Design above illustrates the importance of understanding how air moves within the entire intake system. The figure shows how the GrimmSpeed intake Design compares to other intake Designs with respect to MAF placement and how that affects airflow readings. Since the MAF sensor samples the velocity of incoming air to measure flow in the center of the tube, having an accurate velocity profile at the sensor is the only way to accurately measure airflow. Even though the diameter of our intake is the same as the OEM airbox that alone does Not guarantee accurate readings. The position and clocking of the MAF with respect to the entire system is also very important. All of these seemingly small details end up being extremely important to how the intake affects how the incoming air is Measured by the ECU. Materials In true GrimmSpeed fashion, no corners were cut in the fabrication of each and every one of these intakes. The aluminum heat shield is laser cut, CNC bent and riveted together before receiving a heavy duty Black texture powdercoat. MAF flanges are CNC machined from 6061 Aluminum and the intake tube is fabricated from 5052 aluminum and CNC bent. The air straightener is laser cut from 6061 Aluminum as well, and tumbled before the entire assembly is TIG welded by our expert welders. After welding, each tube receives our heavy duty wrinkle powdercoat and is inspected and cleaned to ensure maximum performance and reliability. Performance and Tuning At GrimmSpeed we love tuners and we like to make sure they love us back. Our intakes are Not oriously easy to tune, and this one is no different. The consistency of the airflow through the MAF sensor makes this intake very predictable and is as easy to tune as the stock airbox. While pro-tuning is always recommended, the Cobb OTS AccessPort Maps can sometimes provide a safe temporary alternative based on your vehicle and level of modification. Dyno Testing was completed on a 2006 WRX, equipped with a GrimmSpeed 3-Port EBCS, Catted Downpipe, EWG Up Pipe and TMIC, being force fed by a VF39 on 91 octane. We used a testing Methodology to show a difference between how a change to only the intake affects the power output, boost, and air to fuel ratios. The car was first equipped with a Cobb OTS Stage 2 tune and was modified only for the VF39 and external wastegate. The airbox was OEM, but with a K and N drop in filter. The tune was then verified and ran multiple times for a boost target of 18psi and an AFR of 11:1. Next, we Installed the GrimmSpeed intake and performed a dyno pull. As expected, the tune was a little too rich, so the tuner adjusted fueling to compensate. The goal was to make the exact same AFR as our OEM airbox pulls, and the tuner accomplished this in only three total pulls on the dyno. The result of this pull, with absolutely no changes to the map other than adjustments to match AFR, was an increase in horsepower and torque nearly everywhere in the entire RPM range. There are maximum gains of Over 13 ftlbs and 18 hp, as shown in the chart to the left. The chart on the right demonstrates that the Design of the GrimmSpeed intake system has decreased restriction Over the stock system (even with an aftermarket drop in filter). This chart shows that while the AFRs for the pull are exactly the same, the gains in peak boost have increased by almost . 75psi. Even more important is the increased boost at Redline of 1.5psi. An increase in boost from only the intake change means that it has removed that much restriction from the intake system. Just looking at the boost curve shows that these relatively small turbos start to run out of breath at higher RPMs, and that the much needed increase in boost that the GrimmSpeed intake creates results in a substantial power gain all the way to Redline. Includes everything: 1x Intake Tube 1x High-flow Dry Filter 1x Silicone Hose Coupler 1x Heat Shield Assembly 3x Hose Clamps 2x MAF Flange Screws 3x Precut Rubber Sealing Strip 3x Airbox to Chassis Bolts Fitment: 2002-2007 Subaru WRX 2004-2007 Subaru STI 2004-2008 Subaru Forester XT Part Numbers: 060074 Intake 02-07 WRX/STI, 04-08 FXT Black 060075 - Intake 02-07 WRX/STI, 04-08 FXT Red Additional Information: title: Cold Air Intake Black For Subaru 02-07 WRX/STI 04-08 FXT GrimmSpeed universal: No sold_as: Each vehicle_type: Car material_l: 6061 Aluminum finish_l: color_l: prop_65_warning: CALIFORNIA WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov country_of_origin: USA size: series: mount: liter: transmission: Guaranteed Fitments: 2002,2007,Subaru,Impreza,WRX 2004,2007,Subaru,Impreza,WRX STI ============================================= SPARKTEC MOTORSPORTS EBAY STORE POLICIES ============================================= Payment: Click the Buy It Now button to safely and securely proceed to checkout. We accept all major credit cards and PayPal. The Sparktec Motorsports eBay Store requires immediate payment. Sales Tax: We are required to collect sales tax whenever applicable in accordance with marketplace facilitator laws. Shipping: FREE Standard Shipping within the contiguous United States. Most orders will ship the same day or the following business day. Please review our shipping policy for handling time and estimated delivery dates. Any address outside of the contiguous United States, please contact Sparktec Motorsports for a shipping quote. Processing begins as soon as an order has been placed, therefore we cannot change, cancel or modify orders once they have been confirmed. To return any unwanted items, please review our return policy for return and exchange instructions. Delivery Time: Once your order ships, please allow an additional 1-5 business days for delivery. Tracking information will be provided to you within 24 hours of shipping out. Because our products ship from warehouses and manufacturers across the US, exact shipping method and times will vary by item. Customer Service: To contact us with questions/comments, please e-mail us using the "Contact seller" link. Most e-mails are answered within 24 hours, including weekends and holidays. Returns: Sparktec Motorsports' eBay Store allows returns of any item, in new and unused condition with original packaging, within 30-days of receiving the item for a refund or exchange. Absolutely NO returns or exchanges allowed on products that have been used, installed, mounted, or missing components. All non-defective returns are subject to a 20% restocking fee. All returns must be accompanied by a Return Merchandise Authorization (RMA) number which can be obtained by contacting us. Any products returned without a Return Merchandise Authorization (RMA) number will be refused. Please contact us in the event you're not satisfied with your purchase as we are more than happy to work with you to ensure a positive experience.

Price: 349 USD

Location: United States

End Time: 2024-12-14T11:14:37.000Z

Shipping Cost: 0 USD