US丨4 Axis Nema23 Dual shaft Stepper Motor 425oz-in/280Ncm &Driver 4A USB CNC Kit

Description: 【USA Stock & Located in USA & fast shipping】Ship from USA Warehouse fast shipping service to US Customers US丨4 Axis Nema23 Dual shaft Stepper Motor 425oz-in/280Ncm &Driver 4A USB CNC Kit for CNC Router Engraving Machine Parcel: 4 x 23HS2430B stepper motor (Dual Shaft,112mm lenght,425Oz-in,3.0A) 4 x FMD2740C stepper motor driver 4.0A (high quality & high performance) 1 x 400W 36V 9.7A DC switching power supply 1 x 4 axis USBCNC breakout board 1 x Hand controller 1 x USB Cable CD include User manual & usbcnc software & registration key Descriptions: 1. 4 Axis USBCNC breakout board 1) Products brief introduction USBCNCV4.0 is a high performance motion controller which based on PC software USBCNC control, the system can complete the conversion from G code to connect stepper motor’s driver motion control signal without requiring any additional hardware and software. This control card is compatible with most stepper driver and servo driver,it is a perfect controller that instead of parallel Mach3 interface board. This interface board is based on USBCNC MK1 and just use in our provide software and function, can not support update the firmware and use other versions of the software and function 2) Computer system requirement Minimum configuration: 1) CPU:1GHz 2) Memory: 512MB 3) 500MB free disk space 4) DIRECTX9 graphics device with WDDM 1.0 or higher driver 5) USB 2.0 interface 6) Net FRAMEWORK 3.5SP1 The recommended configuration: 1) CPU:2GHz dikaryon 2) Memory: 2GB; 3) 1G free disk space 4) DIRECTX9 graphics device with WDDM 1.0 or higher driver 5) USB 2.0 interface 6) Net FRAMEWORK 3.5SP1 3.Production feature 1. After the revision,V4 version using the red PCB board, PCB size is 135.3*82.5mm.; 2. The front of the narrow edge placed with USB communication interface and DB9 hand control interface for the convenience of customers drawn from the case panel directly; 3. The back-end of narrow edge is power input and output interface and 3 relay output interface; relay is strong interference source, relay away from the design of main control chip, it is conducive to the stability of the board; 4. One of the two wide sides is stepper motor and principal axiscontrol signal output; 5. The another side of two wide sides is the emergency stop, manual speed input, limiting input interface; one side for the input, another side output connection mode is simple and convenient; 6. 5V and 12V power module compact independence, security, stability; 7. External ensure the stability of the system work effectively with crystal active and main control chip shield; 8.outline dimension is 135.3*82.5mm, product positioning hole installment dimension is 127*75mm 9. pls note! The software is USBCNC,not mach3, can't use Mach3 software. This item is easy to operate for DIY hobby user,but it is control by USB port,so need more careful for the software install,and pls must be strict read the user manual and follow us. Description:USB 2.0 interfaceSupport system: Win XP/7/8/10Card input voltage: 15-36V;Limit port working voltage: 12VWith Hand control box interface,external hand control box can use this interface to access the system, the interface is standard DB9 form;With manual speed control interface;Limit switch connection methodPower supply voltage 18 to 50V DCWith the current of 1.4-5.6ASubdivision precision 400,800,1600,3200,6400,12800,25600,1000,2000,4000,5000,8000,10000,20000 and 25000 optionalDrive any less than 5.6A current of 2-phase or 4-phase hybrid stepper motorWiring between Motor Driver & Breakout BoardX/Y/Z/A axis stepper motor control signal output, the definition is CK+\CK-\DIR+\DIR-,respectively for pulse positive, pulse negative, direction positive ,direction negative, the board using anode common connection method, so CK+ and DIR+ linked together connect to the 5V on the board,this board does not support the common method. A) USB interface,connect to the computer USB port through this interface.B) Hand control box interface,external hand control box can use this interface to access the system,the interface is standard DB9 form,its definition as shown in the table 4-1.C) Power indicatorD) Board card firmware upgrade button UP and reset button RST, firmware has been updated.E) Manual speed control interface (GND,JOG,VCC)F) Limit input interface. Limit interface definitions are listed in the following table 4-2G) Spindle control selector switch,the switch shift up to the S1 position for the spindle speed control ; switching switch position On below for output control MIST relay .H) External pause and reset interface; the 2 feet marked PAUSE connect suspend switch, 2 feet marked RESET connection reset switch.I) Software MIST control relay output, software settings output marked 3, defined from top to bottom, 3 feet is NC, NO, COM.J) Software FLOOD control relay output ,output marked 2 in the software settings , defined from top to bottom, 3 feet is NC, NO, COM.K) Software SPINDLE control relay output,output marked 1 in the software settings , defined from top to bottom, 3 feet is NC, NO, COM.L) Board working power input,input DC 15~36VM) 12V output interface.as the board marked, GND is -, 12V is +.L) Board working power input,please pay attention to input DC 15~36V,overvoltage or reverse connection will damage the board.N) Spindle control output interface: definitions turn for GND DIR PWM2 12V, respectively is ground,direction signal output, spindle 0-10V speed control signal output, 12V output.O,P,Q,R) A,X,Y,Z axis stepper motor control signal output, the definition is:CK+\CK-\DIR+\DIR-,respectively is impulsion positive, impulsion negative, direction positive, direction negative 2. FMD2740C stepper motor driver FMD2740C DriverPower supply voltage 18 to 50V DCWith the current of 1.4-5.6ASubdivision precision 400,800,1600,3200,6400,12800,25600,1000,2000,4000,5000,8000,10000,20000 and 25000 optionalDrive any less than 5.6A current of 2-phase or 4-phase hybrid stepper motor;Suitable for a variety of small and medium-sized automation equipment and instruments,for example: Small engraving machine, cnc router machine, etc.CharacteristicsHigh-performanceHigh-speed optocoupler signal isolation inputBipolar constant current chopping mode20kHz chopping frequencyElectrical input signal is TTL compatibleStationary current is automatically reduced by halfShape design is convenient for installation FMD2740C driver is suitable for driving small and medium-sized phase current is less than 5.6A 2-phase or 4-phase hybrid stepping motor. Due to the adoption of the new bipolar constant current chopper drive technology, using the same motor can output more speed and power than other drivers. Segments stepper motor running accuracy improved, reduces vibrations and noise reduction.Power supplyThe supply voltage can work normally in between DC18V-50V, FMD2740C driver can use ordinary switch DC power supply, can also be used for transformer and the bridge rectifier and filter capacitor, capacitance desirable 2000U to 5000U. Note rectified voltage ripple crest does not exceed 50V.Recommended the user to use the 24V-36V DC supply , avoid the grid fluctuations over drive voltage operating range.Electrical wiringThe FMD2740C driver can drive all current less than 5.6A 4-wire, 6-wire or 8-wire 2-phase / 4-phase motors. 3. Stepper Motor Technical Specifications Part No.: 23HS2430B Frame Size: NEMA23 Step Angle: 1.8 degree Current: 3.0A/phase Resistance: 1.6 Ohm/phase Inductance: 6.8 mH/phase Holding torque:280N.cm/28kg-cm 425 oz-in Rotor inertia: 800g-cm2 Number of wire leads: 4 Weight: 1.66 kg Length: 112mm General Specification: Step angle accuracy:+ - 5%(full step,not load) Resistance accuracy: + - 10% Inductance accuracy:+ - 20% Temperature rise: 80deg Max(rated current,2 phase on) Ambient temperature ----------—20deg ---- +50deg Insulation resistance:100ohm Min,500VDC Insultion Strength--------500VAC for one minute Datasheet(23HS2430B,Front shaft 8mm dia and 21mm length,back shaft 8mm dia and 11mm length,425 oz-in or 28kg.cm holding torque) This product also has a single shaft for choice, the need to invite the message. Wiring: Red: A+ Green: A- Yellow: B+ Blue: B- 4.Switching power supply400W,Input:100-120VAC or 200-240VAC,50/60Hz,Output:36V,single output switching power supply 400W 36V 11A DC Switching power supplySpecificationModel: S-400W-36VOutput Current:11AOutput Voltage:36VOutput Frequency:85%Output Power: 400WIt comes with built-in cooling fanConnection instructionL: Live wireN: Negative wire+V: DC power output “+”-V: DC power output “-“+V ADJ: output voltage regulation110V or 220VInput: 110-120V AC or 220-240VPlease flip the side input voltage selector switch 5.Usage or Application This products are widely used in engraving machine, printer, medical equipment, embroidery machine, stage lighting, textile automation, printing, packaging and other industries automation equipment Shipping Please open the package and check if there are some damages before sign,if there are some damages,please do not sign and contact us immediately. Problem&Feedback Please give us the opportunityto resolve any problem when you have,we concern your problem and we will try our best to resolve it. Pls contact us before you want to leave any negative feedback. Refund Any reason required for all refund. Item must be in it's original condition and no physical damage,buyer responsible for all shipping cost. When you have the parcel,and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos.

Price: 245 USD

Location: Dallas,TX

End Time: 2024-08-15T03:20:18.000Z

Shipping Cost: 0 USD